Autodesk inventor 2018 tutorials for beginners - heads up display, line, trim, extrude in inventor
1 Helper
2018-01-30
Views 22
Autodesk inventor 2018 tutorials for beginners - heads up display, draw line with angle, trim, extrude in inventor
covered topic in this video are as follows:
- Heads-Up Display
- draw line with angle in inventor
- fillet in inventor
- trim in inventor
- extrude in inventor
in this video i tried to explain about heads up display so i explained it by drawing one triangle. and while drwing triangle i used line, trim ,fillet ,extrude comaand.
Heads-Up Display (HUD) Settings Reference:-
Enable Pointer Input:
When active, the starting point for a sketch element is displayed as Cartesian coordinates (X and Y values) in the value input boxes near the cursor. Disabling Pointer Input turns off the coordinate display of the starting point of a sketch element.
- Pointer Input options:
Use to switch the starting point for a sketch element between Cartesian and Polar coordinates.
Cartesian Coordinates:
When selected, the starting point of a sketch element is displayed with X and Y values relative to the sketch origin of X = 0, Y = 0. This is the default setting.
Polar Coordinates:
When selected, the starting point of a sketch element is displayed with length (L) and angle (A) values relative to the sketch origin of X = 0, Y = 0.
Enable Dimension Input where possible:
When active, values are entered using a combination of both regular Cartesian and Polar coordinates depending on the type of sketch element being drawn. Dimensions are automatically placed on sketch geometry when the TAB key is used to toggle between value input fields.
When this setting is disabled, values are entered using Delta X and Delta Y Cartesian coordinates only. Polar coordinates cannot be used. Dimensions are not placed on sketch geometry even when using the TAB key to toggle between value input fields.
- Dimension Input options:
Cartesian Coordinates:
When selected, both positive and negative Cartesian X and Y coordinates are entered. The values are calculated based on the last pick point.
Polar Coordinates:
When selected, values are entered using a combination of regular Cartesian and Polar coordinates depending on the type of sketch element being drawn. The values are calculated based on the last pick point. This is the default setting.
=============================
Disclaimer:this is not a paid promotion, I just like this product. I'm not being paid for this. this video is only for education purpose.
Copyright Disclaimer Under Section 107 of the Copyright Act 1976, allowance is made for "fair use" for purposes such as criticism, comment, news reporting, teaching, scholarship, and research. Fair use is a use permitted by copyright statute that might otherwise be infringing. Non-profit, educational or personal use tips the balance in favor of fair use.
=============================
Music by
Drankin Song by Kevin MacLeod is licensed under a Creative Commons Attribution license (https://creativecommons.org/licenses/by/4.0/)
Source: http://incompetech.com/music/royal
covered topic in this video are as follows:
- Heads-Up Display
- draw line with angle in inventor
- fillet in inventor
- trim in inventor
- extrude in inventor
in this video i tried to explain about heads up display so i explained it by drawing one triangle. and while drwing triangle i used line, trim ,fillet ,extrude comaand.
Heads-Up Display (HUD) Settings Reference:-
Enable Pointer Input:
When active, the starting point for a sketch element is displayed as Cartesian coordinates (X and Y values) in the value input boxes near the cursor. Disabling Pointer Input turns off the coordinate display of the starting point of a sketch element.
- Pointer Input options:
Use to switch the starting point for a sketch element between Cartesian and Polar coordinates.
Cartesian Coordinates:
When selected, the starting point of a sketch element is displayed with X and Y values relative to the sketch origin of X = 0, Y = 0. This is the default setting.
Polar Coordinates:
When selected, the starting point of a sketch element is displayed with length (L) and angle (A) values relative to the sketch origin of X = 0, Y = 0.
Enable Dimension Input where possible:
When active, values are entered using a combination of both regular Cartesian and Polar coordinates depending on the type of sketch element being drawn. Dimensions are automatically placed on sketch geometry when the TAB key is used to toggle between value input fields.
When this setting is disabled, values are entered using Delta X and Delta Y Cartesian coordinates only. Polar coordinates cannot be used. Dimensions are not placed on sketch geometry even when using the TAB key to toggle between value input fields.
- Dimension Input options:
Cartesian Coordinates:
When selected, both positive and negative Cartesian X and Y coordinates are entered. The values are calculated based on the last pick point.
Polar Coordinates:
When selected, values are entered using a combination of regular Cartesian and Polar coordinates depending on the type of sketch element being drawn. The values are calculated based on the last pick point. This is the default setting.
=============================
Disclaimer:this is not a paid promotion, I just like this product. I'm not being paid for this. this video is only for education purpose.
Copyright Disclaimer Under Section 107 of the Copyright Act 1976, allowance is made for "fair use" for purposes such as criticism, comment, news reporting, teaching, scholarship, and research. Fair use is a use permitted by copyright statute that might otherwise be infringing. Non-profit, educational or personal use tips the balance in favor of fair use.
=============================
Music by
Drankin Song by Kevin MacLeod is licensed under a Creative Commons Attribution license (https://creativecommons.org/licenses/by/4.0/)
Source: http://incompetech.com/music/royal
Report form
RELATED VIDEOS
